stdd (short for "simple time display daemon") is a handy little daemon for the Raspberry PI device that can be used to display the current time.
Helmut Pozimski
8e377343be
refactoring to conform to PEP8 and picking up some suggestions from pylint
|
пре 8 година | |
|---|---|---|
| adafruit_7segment | пре 8 година | |
| config | пре 8 година | |
| debian | пре 8 година | |
| default | пре 10 година | |
| doc | пре 8 година | |
| stddlib | пре 8 година | |
| .bzrignore | пре 11 година | |
| Changelog | пре 8 година | |
| INSTALL | пре 10 година | |
| LICENSE | пре 10 година | |
| MANIFEST.in | пре 10 година | |
| README | пре 10 година | |
| TODO | пре 8 година | |
| setup.py | пре 8 година | |
| stdd | пре 8 година |
README
=== About ===
stdd (short for "simple time display daemon") is a handy little daemon for
the Raspberry PI device that can be used to display the current time on a
7 segment display with a HT16K33 backpack from Adafruit Industries. It
makes heavy use of the python libraries published by Adafruit to control
the display via I2C.
=== USAGE ===
see ./stdd
=== Dependencies ===
stov depends on the following software to be installed:
* python 2.7 or higher (lower 2.x versions might work but are not tested 3.x is not supported)
* python-smbus
* python-pcrtl (optional)
=== COPYING ===
see LICENSE
=== Configuration ===
HW_ADDRESS: hardware address for your display, a common value is
"0x70" use i2cdetect to find yours if it doesn't match
BLINK_COLON: define if you want the middle colon to blink, 0 = off, 1
= on
BRIGHTNESS_HIGH: value used for "high" brightness, valid values are
0-15
BRIGHTNESS_LOW: value used for "low" brightness, valid values are
0-15
SET_BRIGHTNESS_LOW: value used for "low" brightness, valid values are
0-15
SET_BRIGHTNESS_HIGH: time of the day to change the brightness from
low to high
SYSLOG_LEVEL: maximum syslog level to log, stdd uses debug, info and
error
SYSLOG_FACILITY: syslog facility to use for logging (default: user,
can also be daemon)
=== Known issues ===
None yet
=== Installation ==
see INSTALL
stdd (short for "simple time display daemon") is a handy little daemon for
the Raspberry PI device that can be used to display the current time on a
7 segment display with a HT16K33 backpack from Adafruit Industries. It
makes heavy use of the python libraries published by Adafruit to control
the display via I2C.
=== USAGE ===
see ./stdd
=== Dependencies ===
stov depends on the following software to be installed:
* python 2.7 or higher (lower 2.x versions might work but are not tested 3.x is not supported)
* python-smbus
* python-pcrtl (optional)
=== COPYING ===
see LICENSE
=== Configuration ===
HW_ADDRESS: hardware address for your display, a common value is
"0x70" use i2cdetect to find yours if it doesn't match
BLINK_COLON: define if you want the middle colon to blink, 0 = off, 1
= on
BRIGHTNESS_HIGH: value used for "high" brightness, valid values are
0-15
BRIGHTNESS_LOW: value used for "low" brightness, valid values are
0-15
SET_BRIGHTNESS_LOW: value used for "low" brightness, valid values are
0-15
SET_BRIGHTNESS_HIGH: time of the day to change the brightness from
low to high
SYSLOG_LEVEL: maximum syslog level to log, stdd uses debug, info and
error
SYSLOG_FACILITY: syslog facility to use for logging (default: user,
can also be daemon)
=== Known issues ===
None yet
=== Installation ==
see INSTALL